A bolt will not start by hand
Remove it. Confirm BLT-S is used for the feet and BLT-L for the upright, then realign the holes. Stop and use the support route if the correct bolt still catches or the thread looks damaged.
Northstar P-24 tabletop sign stand
Complete assembly instructions for one fictional, nonpowered display prop. All names, codes, parts, and support routes on this page are invented for the example.
Assembly sequence: 7 stepsRead the stop conditions before opening the hardware bag.
P-24 · Rev A
Finished itemOne tabletop sign stand
Direction markBlue arrow faces front
Assembly supportWorkshop lead
CheckedNov 15, 2026
1. Check parts, tools, and the work surface
Keep every part in view until the inventory matches. Do not begin with a missing, cracked, bent, or differently coded piece.
Parts
A · Base1 × BAS-P24 · blue front arrow
B · Rear foot1 × FTR-P24 · two round holes
C · Front foot1 × FTF-P24 · one square mark
D · Upright1 × UPR-P24 · open groove faces front
E · Display shelf1 × SHF-P24 · lip faces up
F · Sign panel1 × SGN-P24 · arrow points up
G · Short bolts4 × BLT-S · silver bag
H · Long bolts and knobs2 × BLT-L, 2 × KNB-P24 · blue bag
Required tools
- Supplied hex key marked TOOL-A
- Soft cloth or mat
- Small tray for fasteners
Prepare the surface
- Use a clear, stable, level table.
- Lay the soft cloth under the base.
- Keep the sign panel flat until step 6.
Stop before assembly if a code does not match, a part is missing, an edge feels sharp, a panel is cracked, a foot is bent, or a bolt thread looks damaged. Do not substitute hardware.
2. Assemble in numbered order
1
Orient the basePlace BAS-P24 label-side down on the cloth. Turn it until the blue arrow points toward you.
Complete when: the label touches the cloth and the arrow is visible at the front edge.
2
Attach the rear footMatch FTR-P24 to the two round-hole marks at the rear. Start two BLT-S bolts by hand, then turn the supplied hex key until the foot sits flush. Do not force further.
Complete when: no gap is visible between the rear foot and base.
3
Attach the front footMatch the square mark on FTF-P24 to the square mark near the blue arrow. Start the other two BLT-S bolts by hand and seat the foot with TOOL-A.
Complete when: both feet sit flat and the base does not rock on the level table.
4
Install the uprightStand UPR-P24 in the center pocket with its open groove facing the blue arrow. Insert both BLT-L bolts from underneath and turn them with TOOL-A until the upright sits flush.
Complete when: the groove faces front, the upright is fully seated, and it does not rotate by hand.
5
Fit the display shelfHold SHF-P24 with its lip facing up. Lower both rear tabs into the lower slots on the upright. Add one KNB-P24 knob on each side and turn by hand.
Complete when: both tabs are hidden in the slots and the shelf lip faces up.
6
Fit the sign panelKeep the printed arrow on SGN-P24 pointing up. Slide the panel straight into the open front groove until both side clips click into view.
Complete when: both clips are visible and the panel edge is level.
7
Run the final checkMove the fastener tray away. Confirm the front arrow, upright groove, shelf lip, two visible panel clips, four short bolts, two long bolts, and two knobs.
Complete when: the stand is stable on the level table and every listed visual check passes.
If a part was fitted backward
Upright groove faces rear: remove the sign panel and shelf, support the upright, remove both long bolts, lift it straight out, rotate it, and repeat steps 4-6. Never twist the upright while it is bolted.
Shelf lip faces down: remove both knobs, lift the shelf straight up, turn the lip upward, reseat both tabs, and reinstall the knobs. Do not pry a tab sideways.
3. Solve a fit problem without forcing the part
The base rocks
Move the stand to a known level table. Check that both feet are in their marked positions and sit flush. Stop if either foot or the base is bent; extra tightening is not the repair.
The sign panel leans
Lift the panel straight out and check that its arrow points up and both clips are intact. Reseat it without twisting. Stop if a clip is cracked or only one clip becomes visible.
The shelf tabs do not enter
Remove the knobs and lift the shelf away. Check that the lip faces up and both tabs align with the lower slots. Do not widen a slot or bend a tab.
4. Product boundary, stop conditions, and support
This fictional P-24 is a nonpowered tabletop display prop.
- Do not use it as a lamp, shelf, seat, step, climbing aid, or load-bearing support.
- Keep fingers outside joints while lowering the shelf and sign panel.
- Stop for any missing or mismatched part, sharp edge, crack, bend, damaged thread, broken clip, or joint that will not sit flush without force.
- Do not drill, trim, glue, bend, or substitute a part to make the example fit.
Fictional support route: stop work, keep the unit disassembled, and give the workshop lead the kit code P-24, the part code, the step number, and a photo of the problem. Resume only after the workshop lead supplies the matching replacement or written correction. A real manual must replace this route with the manufacturer’s current contact and escalation details.
Finished state: the blue arrow and upright groove face front, the shelf lip faces up, both panel clips are visible, both feet sit flush, all listed fasteners are present, and the stand does not rock on a level table.